Getting Started with Plumbing Basics for Bathtub Installation
Getting Started with Plumbing Basics for Bathtub Installation
Blog Article
Have you been searching for tips around Tools You Need to Install a New Bathtub ?
Setting up a bathtub isn't exactly brain surgery, however it does need solid plumbing, woodworking, as well as in some cases, tiling skills. Changing an old tub with a new one is additionally a reasonably difficult project. If the old bathtub is readily obtainable, the job can relocate rapidly; if you need to open a wall surface to remove the old bathtub and also position the brand-new tub, the job is much harder. In either instance, the job is within a house handyman's abilities, although you will require an assistant to move out the old tub as well as set in the new one. Make sure you have qualified on your own for the task and are comfortable trying it. Rather than employing a contractor to take over a halfway-completed project, it is much better to think about utilizing one before you begin. Possibilities are you may need an expert plumber to make tube connections.
This article will aid you mount a brand-new tub in your shower room if you have actually already bought a brand-new bathtub as well as don't require to alter the arrangement of your previous water supply pipelines.
Your devices and product checklist should consist of the following:
Planning for the Installment
To start with, the sustaining frame provided with the bathroom needs to be fitted (if required) according to the producer's guidelines. Next off, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is essential to ensure that if the faucet includes a plastic washer, it is fitted between the bath as well as the faucets. On a plastic bath, it is additionally sensible to fit a supporting plate under the taps device to avoid strain on the tub.
Fit the versatile tap ports to the bottom of the two taps using 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet via the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. See to it you use every one of the supplied washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bath should currently prepare to be suited its final position.
Removing Old Taps
If you require to replace old faucets with brand-new ones as a part of your installment, then the first thing you must do is disconnect the water. After doing so, turn on the taps to drain any water staying in the system. The process of eliminating the existing taps can be rather troublesome because of the restricted access that is commonly the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the taps. Have a cloth all set for the continuing to be water that will come from the pipelines. Once the supply pipelines have been removed, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from turning during this process. As soon as the taps have actually been removed, the holes in the bath/basin will have to be cleansed of any type of old securing substance.
Prior to moving on to fit the brand-new faucets, compare the pipeline links on the old taps to the new taps. If the old faucets are longer than the new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Setting up the Bath tub
Making use of both wooden boards under its feet, place the bathtub in the needed setting. The wooden boards are useful in uniformly spreading out the weight of the tub over the area of the boards instead of focusing all the weight onto four little points.
The next goal is to ensure that the bath tub is leveled all round. This can be attained by examining the level as well as adjusting the feet on the bath tub till the spirit level reads degree.
To set up taps, fit all-time low of the furthest flexible faucet port to the appropriate supply pipeline by making a compression join; after that do the same for the various other tap.
Switch on the water as well as inspect all joints as well as new pipework for leaks and also tighten them if required. Fill up the bath tub and additionally inspect the overflow electrical outlet and the typical electrical outlet for leakages.
Finally, take care of the bath paneling as explained in the maker's user's manual. Tiling and sealing around the bathtub should wait until the bathtub has been utilized at least once as this will settle it into its final placement.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will require a plastic connector to prevent damages to the string. One end of the adapter fits on the plastic tail of the faucet as well as the various other end supplies a connection to the current supply pipelines.
If you require to fit a monobloc, then you will certainly call for decreasing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, place the tap in the installing hole in the bath/basin making certain that the washing machines are in place between the tap and also the sink. Secure the tap in position with the producer provided backnut. When the tap is safely in place, the supply pipelines can be attached to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with typical faucet adapters. The previous kind needs to be connected to the faucet ends first, tightening just by hand. The supply pipelines can later be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bathtub
In the area where the bath meets the ceramic tile, it is necessary to seal the joins with a silicone rubber caulking. This is essential as the fitting can relocate sufficient to break a rigid seal, causing the water to pass through the wall surface between the bathroom and also the tiling, causing problems with moisture as well as feasible leaks to the ceiling listed below.
You can select from a selection of coloured sealers to blend in your fixtures and also fittings. They are sold in tubes as well as cartridges, and also are capable of securing voids approximately a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of soaked paper or soft rope. Keep in mind to always fill the bath tub with water before securing, to allow for the motion experienced when the tub remains in usage. The sealant can fracture rather early if you do not consider this movement before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are likewise easily readily available on the marketplace. It is a good idea to fit the floor tiles using water-resistant or water resistant adhesive and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you appreciate more info about Installing A Bathtub? Try leaving feedback below. We will be delighted to find out your reactions about this review. We are looking forward that you come back again in the near future. For those who enjoyed our post plz be sure to share it. We enjoy reading our article about Tools You Need to Install a New Bathtub .
Pipe burst? Phone now! Report this page